You are here: Home > Restoration > DriEaz > Specialty
Sort By:
Duct Extension Attachment Kit Duct Extension Attachment Kit

Increase the reach and versatility of the Dragon 3600 Mobile Heater. This high-durability heat outlet ducting features a locking attachment rings to hold the ducting in place and a reinforced rib to resist abrasion. Coiled steel construction allows for compact storage and easy handling. Rated to 400°C (752°F) – an ideal match for the Dragon 3600.

Our Price: $80.00
Hard Case - Restoration Kit Hard Case - Restoration Kit

Hard Case - Restoration Kit
Secure and protect your meters and probes

Hard plastic case organizes and protects your sensitive moisture detection tools. Snap-lock fittings secure the contents during transporation and storage. Sturdy foam inserts can be cut to size to hold instruments in place.

Product Features

  • Molded ASB case with protective foam inserts
  • Positive-locking tabs keep contents safe during transport
  • Drilled enclosure tab allows case to be secured with padlock (not included)

Our Price: $152.00
High-Temperature Ducting, 12-in. x 25-ft. High-Temperature Ducting, 12-in. x 25-ft.

High-Temperature Ducting, 12-in. x 25-ft.

Our Price: $170.00
Dragon Fuel Pickup Kit Dragon Fuel Pickup Kit

Dragon 3600 Fuel Pickup Kit
Use the Dragon 3600 with an external fuel tank

Adapts the Dragon 3600 Mobile Furnace for use with a standard 55-gal. fuel tank (purchased separately).Extend Dragon run-times and simplify fuel delivery. For maximum fueling flexibility, quick-connect couplings allow the Dragon to be reconnected to the onboard fuel tank as needed.

Our Price: $345.00
Rescue Mat Panel Kit Rescue Mat Panel Kit

Expand your hardwood floor rescue system with additional panels

Kit includes four 46 × 30 inch mats and two 23 × 30 inch mats. Two sizes of mats allow for multiple configurations and maximum flexibility, and installation is fast and easy with just one hose connection per mat. Gasket edges provide a powerful seal and eliminate the need for taping down mats.

Our Price: $455.00
AirWolf Airmover AirWolf Airmover

Unrivalled air delivery

The AirWolf provides an unbeatable combination of powerful CFM and strong static pressure. Optimized for use with the WolfPack hardwood floor drying system, the AirWolf/WolfPack combination dries wood floors from the bottom out and can help avoid costly repair bills.

Our Price: $629.00
DriForce™ Accessory Kit DriForce Accessory Kit

DriForce Accessory Kit
Dry inside walls without damage

When used with the DriForce Airmover base unit(purchased separately), the Accessory Kit allows you to direct high-pressure air into wet wall cavities and other areas for fast, effective drying. You only need to make quarter-inch holes – this can usually be done behind the baseboards – to introduce warm, dry air into wall cavities, behind cabinets, tubs, under stairwells, and more.

Are you new to the DriForce System? We recommend the complete DriForce Interair Drying System, which includes the airmover base unit and all the components of the Accessory Kit described here.

The Accessory Kit includes:

  • 13 7 ft. hoses w/cuffs
  • 8 manifolds
  • 1 400 ft. coil of cut-to-size PVC tubing
  • 100 ¼ in. injector nozzles
  • 4 manifold end caps
  • 5 coupler fittings
  • 2 T-fittings
  • 25 tube extender connectors
  • 2 wheeled duffle bags

Our Price: $955.00
DriForce™ Base Unit DriForce Base Unit

DriForce Airmover
Base unit only

This compact specialty airmover provides up to 38 inches (97 cm) of static pressure. Designed for use with the DriForce Interair Drying System and the Rescue Mat Hardwood Floor Drying System, the DriForce Airmover delivers the performance and reliability you need to tackle difficult drying situations.

Product Features

  • Produces up to 38 inches of static pressure
  • Draws only 3 amps on average
  • Force air in or vacuum air out
  • Stackable for easy storage and transport
Product Specifications
Model F211
Dimensions (H × W × D) 14 × 14 × 12 in.
36 × 36 × 30 cm
Weight 14.5 lb. | 7 kg
Max. Power 4.8 amps (115V)
Working static pressure 38 in. | 97 cm

Our Price: $1,595.00
DriForce InterAir Drying System DriForce InterAir Drying System

Product Overview

For water-damage restoration and restorative drying work, the Dri-Eaz F211 DriForce InterAir Drying System delivers high-pressure air to remove moisture trapped in structural cavities. To speed up drying time, use the Dri-Eaz DriForce Wall Drying System to simultaneously dry different target areas, including ceilings, dry walls, behind or under cabinets, and headers. This compact and lightweight drying system provides every accessory to restore even the most difficult-to-access areas. This drying system is designed with high-pressure air technology and uses less than 3 amps of 115-volt power.

Please Note: This DriForce System is not designed to extract water or debris. Proper use of this system is for the movement of air only.

Complete System Includes

  • DriForce Air Mover
  • 13 7-foot hoses with cuffs
  • 8 manifolds
  • 1 400-foot coil of PVC tubing
  • 100 ¼-in. injector nozzles
  • 4 manifold end caps
  • 5 coupler fittings
  • 2 T-fittings
  • 25 tube extender connectors
  • 1 muffler
  • 2 wheeled duffel bags

Drying Speed Efficiency

With the Dri-Eaz DriForce InterAir Drying System, you can deliver a high-quality restoration service to your customers by returning structures to pre-loss conditions in less time, saving the property owner the cost of reconstruction. For maximum drying efficiency, the Dri-Eaz F211 DriForce InterAir Drying System employs four drying mechanisms:

  • Injection Mode: Pushes dry air into structural cavities
  • Extraction Mode: Pulls moist air out of structural cavities
  • Dehumidification: When extra-dry air is required for drying difficult areas, position the output airflow from a dehumidifier near the DriForce air inlet
  • Heat: The blow motor generates heat, which increases the temperature of the air that enters the airflow for increased drying efficiency

Other system components designed for drying efficiency include:

  • Air Nozzle Fins: To form a tight seal between the air nozzle and drilled hole, the fins lock in place. This is useful for drying ceilings.
  • High Coverage: Treat over 90 feet of 2 x 4-constructed wall at one time.
  • High-Pressure Air: Delivers up to 38 inches of static pressure while using less than 3 amps of 115-volt power.

Versatility for Every Restoration Project

Together with the Injection/Extraction drying modes, the Dri-Eaz DriForce Wall Drying System contains every accessory to dry difficult-to-access areas as well as challenging materials, including lath and plaster, double-sheeted or fire walls, insulated walls, and walls covered with vinyl wallpaper or impermeable paint. To speed up drying time, the DriForce is designed to dry a combination of structures at the same time, including walls, cabinets, headers, and ceilings.

Additional Features

  • Minimal Damage: The DriForce air nozzles need installation holes that are less than ¼”, cutting back on time required to patch and repair holes.
  • Durable Construction: Built for years of service for even the most difficult of restoration jobs, the DriForce is built with durable, long-lasting materials, including a stainless steel-based and double-wall polyethylene housing.


The Dri-Eaz DriForce InterAir Drying System dries wet walls, ceilings, cabinets, and headers without damage.

What Customers Love

  • 2 Drying Methods - Force air in or vacuum air out. This system offers 2 effective drying methods.
  • Low Power - The system averages just 3 amps in use.

Things To Consider

  • Compatible with Rescue Mat System - Use with the Dri-Eaz Rescue Mat Panel System fast drying of hardwood floors.

Our Price: $2,175.00
Dragon 3600 Mobile Furnace Dragon 3600 Mobile Furnace

The diesel-powered Dri-Eaz Dragon Mobile Furnace reduces drying time and warms individual areas in a variety of applications, from water damage restoration to temporary emergency heating in the field. This industrial-strength super-portable heater generates 120,000 BTUs of heating power to create a temperature rise of up to 145 degrees F. The furnace sits on large smooth-rolling wheels that simplify transport—just roll the heater on the back of a truck and transport it to the desired spot. It features straightforward controls that are easy to use and an amazing 36-hour runtime on a single fuel tank.

Dry Heat Aids Drying and Creates Comfortable Warmth

The Dri-Eaz F535 Dragon 3600 Mobile Furnace is an indirect-fired furnace that produces heated air for water damage restoration, structural drying, construction, event shelter heating, and other temporary heating applications. Its unique design keeps combustion separate from the heated air, allowing it to heat without adding moisture, fumes, or smoke. The furnace's electrically powered fan directs heated air into a structure through ducting while the included remote thermostat cycles operation on and off to maintain your desired level of heat. Use the furnace in nearly any situation where you need clean, dry temporary heat.

Added Accessories for Convenience

The Dri-Eaz Dragon comes with added accessories to make customized operation convenient. You'll receive 25 feet of high-temperature ducting, a thermostat with a 50 foot remote sensor, a stack and rain cap, as well as 4 ounces of Diesel Guard, a fuel conditioner and winterizing treatment.

Additional Features and Specifications

  • Extended runtimes - Get 36 hours of operation without refueling.
  • Powerful temp rise - 145 degrees F with weather shield installed; 120 degrees without weather sheild.
  • Overheat Safety Protection - In the event of overheating, an overheat shutoff switch powers off heating and runs the fan until the unit is cool.
  • Precision heat control - Thermostat with remote sensor (included) to help comply with RIA Safe Harbor clause.
  • Processes 780 CFMs - The furnace processes 780 cubic feet of air per minute for high-volume heating of large areas.
  • Indirect-fired operation - Provides clean heat and no additional moisture - speeds drying. Use with positive or negative pressure setups.
  • Highly mobile - Ball bearing wheels and semi-pneumatic tires keep rolling in cold weather.
  • Fuel Consumption: .85 gallons per hour
  • Fuel Type: Diesel
  • Total Weight: 495 lbs. on a full tank; 250 lbs. on empty
  • Safety: CSA listed


The Dri-Eaz Dragon Mobile Furnace provides 120,000 BTUs of dry heat to aid drying applications or serve as a reliable temporary source of heat in the field.

Things To Consider

  • Safety is Key - This is a diesel-powered industrial heater designed for powerful heating in the field. Be sure to read the owner's manual and follow all safety recommendations during use.

Our Price: $4,295.00